16" 100% Kevlar terry cloth sleeves with cotton knit wrists. Protects your entire arm.
|
Deluxe duty gloves. Split tanned, soft, flexible and heat resistant. Fully lined gloves and cuffs. 13.5" from middle finger to cuff, 5.5" wide.
|
 Soft insulating bricks are used for general kiln construction because they are lightweight and easy to cut without the use of special saws or tools. Each brick measures 9.0"x4.5"x2.5". Rated to 2300°F
|
Soft insulating bricks are used for general kiln construction because they are lightweight and easy to cut without the use of special saws or tools. Each brick measures 9.0"x4.5"x2.5". Rated to 2600°F
|
Outstanding insulating properties at elevated temperatures and excellent thermal stability and retain their original soft fibrous structure to its maximum continuous use temperature.
|
NiCr A (80Ni 20Cr). A flexible wire capable of use up to Cone 5 (2205°F). In short lengths, can be suspended between two kiln posts to support beads or jewelry in firing. 15 gauge (3/64" diameter). Sold by the foot.
|
A 2" diameter Ceramic Washer used to secure Ceramic Fiber to an outer frame. For use with nichrome tie wire. Works well with 15 gauge Nichrome wire (pictured, but not included). Can be fired up to Cone 12.
|
Vent Two Kilns with One Vent Motor; the EnviroVent2 has the capability of venting 2 large kilns (up to 12 cu/ft chambers) with this optional Dual Exhaust Kit. The kit is easy to install and comes with the ducting Y, additional ducting and collection cup.
|
From $701.00 to $1,186.00
With Downdraft Venting, the kiln is kept under negative pressure. Gases are mixed with fresh room air, pulled out of the kiln near the bottom and exhausted to the outside through a duct. 8 ft. x 3 in. Flexible Aluminum Duct.
|
With Downdraft Venting, the kiln is kept under a slight negative pressure. Gases are pulled out of the kiln near the bottom, mixed with fresh room air and exhausted to the outside through a duct. 8ft x 4 in. flexible Duct.
|
VentMaster Expansion Kit allows you to add another kiln at a fraction of the cost of a new vent. Accessory for the Orton Ventmaster.
|
VentMaster Hose Kit extends the distance between the blower motor and the collector cup. Accessory for the Orton Ventmaster.
|
A high temperature protective coating for kiln shelves and other areas inside the kiln that may be subjected to dripping glaze during firing.
|
A protective coating for kiln shelves and other areas inside the kiln that may be subjected to dripping glaze during firing.
|
A protective coating for kiln shelves and other areas inside the kiln that may be subjected to dripping glaze during firing.
|
Use with firebrick and insulating firebrick. Air setting. Maximum service temperature 2900°F.
|
The Fireball Oxyprobe is a precision instrument designed to improve the firings in fuel-fired kilns.
|
Analogue pyrometer to assist in reading the interior temperature of your kiln; reads up to 2500°F. Meter marked so you can make both Centigrade or Fahrenheit readings.
|
Digital handheld pyrometer to assist in reading the interior temperature of your kiln; Single Input K-Type Thermocouple Thermometer with a -58 to +2,462 °F range.
|
Replacement Temperature Probe for TPI341KC1 Digital Pyrometer
|
Wire to connect an analogue pyrometer to thermocouple. (sold by the foot).
|
K Type Thermocouple; available in 6", 8" or 12" lengths.
|
12" Protection Tube for K Type Thermocouple. Inner Diameter 0.45", Outer Diameter 0.7"
|
Thermocouple for Skutt KM Kilns; thermocouple only, no block. 6".
|
Ceramic 9" OxyProbe Protection Tube replacement.
|
Colloid Silica Rigidizer. This liquid material has several uses in connection with fiber insulation materials. Sold by the gallon.
|
Used to support beads, rings and many other small articles during kiln firing. Approximately 11" long, the Ceramic Bead Bars are designed with a special, high temperature alloy. Support properly. Approx 0.15" dia.
|
For small cones. Holding pyrometric cones in the correct position is the way to obtain the most accurate indication of proper firing. Heat resistant wire gives these holders long life and durability. Five holders in each package.
|
For large cones. Holding pyrometric cones in the correct position is the way to obtain the most accurate indication of proper firing. Heat resistant wire gives these holders long life and durability. Five holders in each package.
|
For pyrometric small cones and pyrometric bars. Fits all models of Kiln-Sitter. Each cone support is approximately 1.35" long by 0.35" wide.
|