Refractories & Firing

Products In This Category

Displaying products 61 - 90 of 134 results
Page 3 of 5 Page moveprev12345movenext
$36.05
#4x6 Steel Multipoint Stilts. Sold in sets of 12.
$23.10
Setter for beads, buttons, trinkets, etc. Length is 4”, height is 2”. Comes with four 6” rods. Maximum recommended firing range: 2250° F.
$47.55
Two durable stoneware supports with 10" long wires, provide a versatile, space-saving device for firing macrame beads and other larger hanging objects. Base is 3.25" x 1.5"; 6.5" H and uprights are 2" W x 5/16" thick.
$18.00
This block is made of aloxite, a fine, hard abrasive material. Excellent for grinding glaze runs and rough spots on both glazes and bisque ware. 200 mesh, 80 grit, K grade. 2"x 4"x 3/4"
$9.00
After firing, remove unsightly stilt marks with this Aloxite Stilt Mark Stone. In seconds, you can gently and easily remove stilt marks with these slender 4" long, 3/8" x 3/8" bar. 200 mesh, 80 grit, K grade.
$17.00
This block is made of aloxite, a fine, hard abrasive material. Excellent for grinding glaze runs and rough spots on both glazes and bisque ware. 200 mesh, 80 grit, K grade. 2"x 2.5"x 1"
$26.00
A fluted, silicon carbide brick 8" long, 2" x 2" square bar. Very effective at cleaning glaze drips and excessive build up of kiln wash from kiln shelves.
$35.00
A fluted, silicon carbide brick 6" long, 3" x 1" bar. Very effective at cleaning glaze drips and excessive build up of kiln wash from kiln shelves.
$6.95
2" long, 13/16" top diameter, 1.75" bottom diameter plug for kiln peepholes.
$7.75
approximate measurements: 3.5" long, 1.25" top diameter, 0.75" bottom diameter plug for kiln peepholes.
$15.00

Designed especially for use with the Kiln-Sitter, their uniform shape makes consistent placement easy. In boxes of 50. Each pyrometric bar is approximately 1" long.
$12.80

Used to trigger the Kiln-Sitter or where space is at a premium. The tapered shape offers adjustment in firing range. In boxes of 50 cones. Each small cone is approximately 1.2" long.
ratingratingratingratingrating
$17.40

The original Pyrometric Cone. Use in a cone holder on a kiln shelf for visual firing, testing or monitoring. In boxes of 50 cones. Each large cone is approximately 2.5" long.
$12.80

These unique cones, complete with a built-in base, make accurate performance easy and consistent. Perfect for witness cones. In boxes of 25. Each self-supporting cone is approximately 2.5" long.
$55.15
This venturi burner is complete with a flame retention feature within a single casting. The overall length of this burner is 8", and the range of BTU's spans from 17,490 BTU minimum to 78,440 BTU maximum...
$249.00
This venturi burner kit is an excellent option for your raku kiln; for use with propane.
$307.66
This burner is 12” long and will produce between 29,900 to 356,400 BTUs depending on the gas pressure, type of gas and size of orifice.
$304.90
This burner is 17” long and will produce between 48,900 to 495,300 BTUs depending on the gas pressure, type of gas and size of orifice.
$384.90
This burner is 21” long and will produce between 58,700 to 649,400 BTUs depending on the gas pressure, type of gas and size of orifice.
$4.15
1/2" x 1/4" Hose Bushing (red).
$2.75
Burner accessory. Hose fit connector. 9/16 18 LH x 1/4 MNPT.
$3.75
Orifice replacement for Laguna and Venturi burners for natural gas. ~1/8" aperture.
$3.75
Orifice replacement for Laguna and Venturi burners for propane. ~1/16" aperture, #50.
$22.95
Use to control a fuel's flow with the turn of a handle. Inner thread measures 1/4". Brass body, 600 WOG rated.
$19.95
Use to control a fuel's flow with the turn of a handle. Inner thread measures 1/2". Brass body, 600 WOG rated.
$29.95
Use to control a fuel's flow with the turn of a handle. Inner thread measures 3/4". Brass body, 600 WOG rated.
$41.90
Use to control and regulate a fuel's flow.
$34.00
Use to control and regulate a fuel's flow.
$16.95
Use to control and regulate a fuel's flow.
$31.50
Use to control and regulate a fuel's flow.
Page 3 of 5 Page moveprev12345movenext